Rekuperators priekš Vallox ValloMulti 200 SC
Vallox ValloMulti 200 SC iekārtu nomaiņas siltummainis
RX un RX-P ir moderni pretplūsmas apmainītāji ar ribām, kas izgatavotas no izturīga alumīnija un plastmasas. Pretplūsmas siltummainis ir mazāka apjoma pēctecis.
efektīvs šķērsapmainītājs. Pretplūsmas siltummainis nepārvada mitrumu vai smakas. Tā efektivitāte pārsniedz 95%.
Pateicoties šīm īpašībām, kā arī katras izgatavotās detaļas pārbaudītajai hermētiskai iedarbībai, tā tiek izmantota gan pasīvo māju siltuma atgūšanas iekārtās, gan rūpnieciskos pielietojumos.
- Efektivitāte līdz pat vairāk nekā 95%
- Lieliska cenas un vērtības attiecība
- Labākais līdzsvars starp spiediena zudumu un efektivitāti
- Īpaši izstrādāta ribu ģeometrija optimālām siltuma pārneses īpašībām
- 100% hermētiskuma pārbaude
- Divkāršās šuves tehnoloģija visai produktu līnijai = labākā hermētiskums tirgū
- Materiāls: alumīnijs
- Eurovent, ILH, TÜV, EAC, QMS, OHMS, EMS sertifikāti
Šis siltummainis ir izmēru ziņā identisks Vallox ValloMulti 200 SB rekuperācijas iekārtu rekuperatoriem. Tomēr šī nav oriģinālā rezerves daļa, ko piegādā un uzstāda ierīces ražotājs, tāpēc tās lietošana ir RJ lietotāja ziņā.
 |
|
 |
|
Datu lapa
- Garantijas ilgums
- 36 mēneši
- EUROVENT sertifikācija:
- JĀ
- Līstu materiāls:
- Alumīnijs
- Apvalka materiāls:
- Alumīnijs
- Darba temperatūra [°C]
- No -20 līdz +80
- Iekārtas ražotājs
- Vallox
- Izcelsmes valsts
- ES
RECUTECH are equipped with the latest enthalpic membrane METALPIC. They excel in top-class heat and humidity recovery, high resistance to pressure differences, and long service life. They are among the most advanced enthalpic heat exchangers currently available on the market.
ZERN are fully plastic enthalpic heat exchangers, very efficient, with slightly better moisture transfer, but with higher pressure loss.
No, never block the condensate drain.
Even though enthalpic heat exchangers produce only a minimal amount of condensate due to moisture transfer, in severe frost and specific humidity conditions, condensate can still occur. Blocking the drain could cause irreversible damage to your unit.
Since an enthalpic heat exchanger also transfers humidity, it might seem that the risk of mold is higher. In reality, however, all moisture is carried away with the fresh air, so there is no risk of mold growth.
Our recommendation is to never switch off the unit during the winter months, so that moisture is continuously removed. If you still need to shut down the unit, remove the exchanger, rinse it with clean water, dry it thoroughly, and only then reinstall it
Yes, installation is simple. Just follow the instructions provided with your unit. As with a standard exchanger, it needs to be removed occasionally for cleaning – the process is the same, except that you put the enthalpic exchanger back in instead.
No, caring for an enthalpic heat exchanger is no more demanding than for a standard one. Maintenance is described in the user manual and in our video guide. In short: first vacuum the exchanger with a soft brush attachment, then rinse it with clean water (max. 50 °C). Never use compressed air or a pressure washer.
After rinsing, allow all water to drain completely. Remaining moisture can be carefully blown out with a regular hairdryer, but always use cold air only. Once the exchanger is completely dry, place it back into the unit in the same orientation as before removal.
We do not recommend using chemicals for cleaning. Only if disinfection is absolutely necessary may a weak solution of peracetic acid be used, followed by very thorough rinsing with clean water.
Vallox ValloMulti 200 SC iekārtu nomaiņas siltummainis