Recuperator voor Vallox ValloMulti 200 SC
Vervangende warmtewisselaar voor Vallox ValloMulti 200 SC -units
RX en RX-P zijn moderne tegenstroomwarmtewisselaars met vinnen van duurzaam aluminium en kunststof. De tegenstroomwisselaar is de opvolger van de minder
efficiënte kruiswisselaar. De tegenstroomwisselaar transporteert geen vocht of geuren. Het rendement bedraagt meer dan 95%.
Dankzij deze eigenschappen, in combinatie met de geteste dichtheid van elk geproduceerd onderdeel, vindt het zijn toepassing in zowel warmteterugwinningsunits van passiefhuizen als in industriële toepassingen.
- Rendement tot ruim 95%
- Uitstekende prijs-kwaliteitverhouding
- De beste balans tussen drukverlies en efficiëntie
- Speciaal ontwikkelde vingeometrie voor optimale warmteoverdrachtseigenschappen
- 100% lektesten
- Dubbele naadtechnologie voor de gehele productlijn = beste dichtheid op de markt
- Materiaal: aluminium
- Eurovent-, ILH-, TÜV-, EAC-, QMS-, OHMS- en EMS- certificeringen
Deze wisselaar is qua afmetingen identiek aan de recuperatoren in de Vallox ValloMulti 200 SB recuperatie-units. Dit is echter geen origineel reserveonderdeel dat door de fabrikant van het apparaat wordt geleverd en geïnstalleerd. Het gebruik ervan is dus ter beoordeling van de RJ-gebruiker.
 |
|
 |
|
Datasheet
- Garantieduur
- 36 maanden
- EUROVENT-certificering:
- JA
- Lattenmateriaal:
- Aluminium
- Omhulselmateriaal:
- Aluminium
- Bedrijfstemperatuur [°C]
- Van -20 tot +80
- Fabrikant van de eenheid
- Vallox
- Land van herkomst
- EU
RECUTECH are equipped with the latest enthalpic membrane METALPIC. They excel in top-class heat and humidity recovery, high resistance to pressure differences, and long service life. They are among the most advanced enthalpic heat exchangers currently available on the market.
ZERN are fully plastic enthalpic heat exchangers, very efficient, with slightly better moisture transfer, but with higher pressure loss.
No, never block the condensate drain.
Even though enthalpic heat exchangers produce only a minimal amount of condensate due to moisture transfer, in severe frost and specific humidity conditions, condensate can still occur. Blocking the drain could cause irreversible damage to your unit.
Since an enthalpic heat exchanger also transfers humidity, it might seem that the risk of mold is higher. In reality, however, all moisture is carried away with the fresh air, so there is no risk of mold growth.
Our recommendation is to never switch off the unit during the winter months, so that moisture is continuously removed. If you still need to shut down the unit, remove the exchanger, rinse it with clean water, dry it thoroughly, and only then reinstall it
Yes, installation is simple. Just follow the instructions provided with your unit. As with a standard exchanger, it needs to be removed occasionally for cleaning – the process is the same, except that you put the enthalpic exchanger back in instead.
No, caring for an enthalpic heat exchanger is no more demanding than for a standard one. Maintenance is described in the user manual and in our video guide. In short: first vacuum the exchanger with a soft brush attachment, then rinse it with clean water (max. 50 °C). Never use compressed air or a pressure washer.
After rinsing, allow all water to drain completely. Remaining moisture can be carefully blown out with a regular hairdryer, but always use cold air only. Once the exchanger is completely dry, place it back into the unit in the same orientation as before removal.
We do not recommend using chemicals for cleaning. Only if disinfection is absolutely necessary may a weak solution of peracetic acid be used, followed by very thorough rinsing with clean water.
Vervangende warmtewisselaar voor Vallox ValloMulti 200 SC -units