Recuperator til Vallox ValloMulti 200 SB
Udskiftningsveksler til Vallox ValloMulti 200 SB- enheder
RX og RX-P er moderne modstrømsvekslere med finner lavet af slidstærkt aluminium og plast. Modstrømsveksleren er efterfølgeren til den mindre
effektiv krydsveksler. Modstrømsveksleren overfører ikke fugt eller lugte. Dens effektivitet overstiger 95%.
Det er takket være disse egenskaber, sammen med den testede tæthed af hvert enkelt fremstillet stykke, at det finder sin anvendelse både i varmegenvindingsenheder i passivhuse og i industrielle applikationer.
- Effektivitet op til over 95%
- Fremragende værdi for pengene
- Den bedste balance mellem tryktab og effektivitet
- Specielt udviklet finnegeometri for optimale varmeoverføringsegenskaber
- 100% lækagetest
- Dobbeltsømteknologi for hele produktlinjen = bedste tæthed på markedet
- Materiale: aluminium
- Eurovent, ILH, TÜV, EAC, QMS, OHMS, EMS- certificeringer
Denne veksler er dimensionelt identisk med rekuperatorerne i Vallox ValloMulti 200 SB rekuperationsenheder. Dette er dog ikke en original reservedel leveret og installeret af producenten, så brugen af den er op til RJ-brugeren.
 |
|
 |
|
Produktinformation
- Délka záruky
- 36 měsíců
- Certifikace EUROVENT:
- ANO
- Materiál lamel:
- hliník
- Materiál opláštění:
- hliník
- Provozní teplota [°C]
- od -20 do +80
- Země původu
- EU
RECUTECH are equipped with the latest enthalpic membrane METALPIC. They excel in top-class heat and humidity recovery, high resistance to pressure differences, and long service life. They are among the most advanced enthalpic heat exchangers currently available on the market.
ZERN are fully plastic enthalpic heat exchangers, very efficient, with slightly better moisture transfer, but with higher pressure loss.
No, never block the condensate drain.
Even though enthalpic heat exchangers produce only a minimal amount of condensate due to moisture transfer, in severe frost and specific humidity conditions, condensate can still occur. Blocking the drain could cause irreversible damage to your unit.
Since an enthalpic heat exchanger also transfers humidity, it might seem that the risk of mold is higher. In reality, however, all moisture is carried away with the fresh air, so there is no risk of mold growth.
Our recommendation is to never switch off the unit during the winter months, so that moisture is continuously removed. If you still need to shut down the unit, remove the exchanger, rinse it with clean water, dry it thoroughly, and only then reinstall it
Yes, installation is simple. Just follow the instructions provided with your unit. As with a standard exchanger, it needs to be removed occasionally for cleaning – the process is the same, except that you put the enthalpic exchanger back in instead.
No, caring for an enthalpic heat exchanger is no more demanding than for a standard one. Maintenance is described in the user manual and in our video guide. In short: first vacuum the exchanger with a soft brush attachment, then rinse it with clean water (max. 50 °C). Never use compressed air or a pressure washer.
After rinsing, allow all water to drain completely. Remaining moisture can be carefully blown out with a regular hairdryer, but always use cold air only. Once the exchanger is completely dry, place it back into the unit in the same orientation as before removal.
We do not recommend using chemicals for cleaning. Only if disinfection is absolutely necessary may a weak solution of peracetic acid be used, followed by very thorough rinsing with clean water.
Udskiftningsveksler til Vallox ValloMulti 200 SB- enheder